TTL to RS485 converter module [ Serial UART Interface , Auto Direction Control ]

฿50.00 มีค่าจัดส่ง

Recommended Standard no. 485 โมดูลแปลงสัญญาณมาตรฐานการสื่อสารข้อมูลดิจิตอลแบบอนุกรม (serial communication) ผ่านอินเตอร์เฟซ UART ( เข้ากันได้กับ Arduino , ESP และ Raspberry Pi ) มีวงจรควบคุมทิศทางอัตโนมัติ auto direction control โดยไม่ต้องควบคุมทิศทางการรับ-ส่งข้อมูล ผ่านขา DE/RI

เหลือ 3 ชิ้น

รหัสสินค้า: imi410003 หมวดหมู่:

รายละเอียดสินค้า

รายละเอียดเพิ่มเติม

TTL to RS485 converter module [ Serial UART Interface , Auto Direction Control ]

 

The SCM TTL to RS-485 Interface module provides a robust automatic bi-directional interface from TTL to long-line RS-485.

Recommended Standard no. 485 โมดูลแปลงสัญญาณมาตรฐานการสื่อสารข้อมูลดิจิตอลแบบอนุกรม (serial communication) ผ่านอินเตอร์เฟซ UART ( เข้ากันได้กับ Arduino , ESP และ Raspberry Pi ) มีวงจรควบคุมทิศทางอัตโนมัติ auto direction control โดยไม่ต้องควบคุมทิศทางการรับ-ส่งข้อมูล ผ่านขา DE/RI

ส่วนหัว 1 x 4 (ด้าน TTL)

  • VCC  = Vcc – เชื่อมต่อกับ 3.3V หรือ 5V เพื่อให้ตรงกับกำลังไฟของ MCU
  • RXD  = รับข้อมูล – เชื่อมต่อกับอินพุต RXD TTL บน MCU
  • TXD  = ส่งข้อมูล – เชื่อมต่อกับเอาต์พุต TXD TTL บน MCU
  • GND =    พื้นดิน เชื่อมต่อกับกราวด์บน MCU

1 x 3 ขั้วต่อสกรู (ด้านข้าง RS-485)

  • A+      = ข้อมูล ‘A’ Non-Inverted Line เชื่อมต่อกับ A+ บนโมดูลอื่นๆ
  • B-      = ข้อมูล ‘B’ Inverted Line เชื่อมต่อกับ B- บนโมดูลอื่น ๆ
  • GND = กราวด์

FEATURES

  • 3.3V and 5.0V signal perfectly compatible
  • Working temperature range: -40 ℃ to + 85 ℃
  • Automatic bi-directional transmission control
  • Uses differential signaling for noise immunity
  • Transmission distance up to kilometers (with 850 meters of 2 * 1.5 cable to do the test, it is recommended to use in the 800 meters, more than 800 meters, please add repeaters)
  • Speeds up to 2.5Mbit/Sec
  • Multi-drop supports up to 32 devices on same bus
  • Built-in poly fuses for over-current protection
  • Built-in transient surge protection diodes for over-voltage protection
  • Transmit and receive indicator LEDs
  • Has RXD, TXD signal lights to observe send and receive status
  • Semi-hole process design, the thickness of 0.8mm, makes it easy to use as a combo board, it can also be welded terminal use

    Termination Resistors

    There are 4.7K pull-up resistors on the A/B differential lines.  These pull the lines to a known state when data is not being transmitted.

    Finally there is a single 120 ohm termination resistor.  This resistor goes between the A & B differential lines on the modules at each end of the cable to prevent reflections. [On Position R0 or R13]  As shipped, the resistor is not in-circuit.  To put the resistor in-circuit, the solder pads at location R0 should be shorted with solder or a wire.  If using in a multi-drop configuration, the modules on the two ends of the line should add these resistors.  Modules in the middle of the line should not use these resistors to prevent loading the lines too heavily as shown in the pic above.

    For benchtop testing with short cables, this resistor can usually be ignored.

ข้อมูลเพิ่มเติม

ข้อมูลเพิ่มเติม

น้ำหนัก 100 กรัม
ขนาดขนส่ง 10 × 4 × 3 เซนติเมตร
ประเภทสินค้า

ตัวแปลงสัญญาณ

ผู้ผลิต

ประเทศจีน

ผู้นำเข้า

อิมิคอน ซิสเท็ม

ผู้จัดจำหน่าย

ร้านอิมิคอนซิสเท็ม 14/44 ถ.ลำพูน-ป่าซาง ต.ในเมือง อ.เมือง จ.ลำพูน

วิธีใช้

ใช้แปลงสัญญาณ

คู่มือการใช้งาน

สินค้าภายในกล่อง

ตัวอย่างการโปรแกรม

ตัวอย่างโปรเจค

⚠️ รุ่นที่ใหม่กว่า

คุณอาจจะชื่นชอบ…